Knowledge

Analyzing the knowledge of anilox rollers in ink flexographic printing machines

Jul 09, 2024 Leave a message

1. Pressure of the inking device:
  
This pressure is the pressure between the ink roller and the metal mesh roller. Its main function is to control the ink consumption of printing and evenly transfer ink.
  
If the pressure between the two rollers is high, the amount of ink on the metal mesh roller will be less; On the contrary, they consume more ink. At the same time, if the pressure between the two rollers is too small (i.e. the gap is too large), once it reaches the critical point of the mesh height, it loses the function of the mesh roller to transfer ink, resulting in uneven ink consumption on the printing plate, difficult control of ink volume during printing, and ultimately causing the printed product to have a thick film, resulting in sticky ink stains, poor clarity, blurred dots, line spreading, and blurred handwriting.
  
If the pressure between the two rollers is too tight (with a small gap), the ink consumption on the metal mesh roller is relatively reduced, and the dot can be printed clearly. The characters and lines can be printed clearly and straight, but lack a certain amount of ink and gloss. At the same time, it is necessary to prevent excessive pressure between the two rollers from causing bending at both ends of the metal mesh roller and the ink roller, jumping of the printing machine gear, and tooth breakage.
  
The principle of the magnitude of this printing pressure generally depends on the characteristics of the product, and the pressure between the two rollers of the wire mesh product can be relatively larger; Small text, line pressure can also be slightly higher; Large characters and on-site products can be relatively small. At the same time, the pressure is related to the size of the printing area. Generally, for larger printing areas, the pressure can be lighter to increase the amount of ink, thereby improving the density, brightness, and brightness of the field. Generally, for smaller or more delicate printing areas, the pressure should be slightly higher to reduce ink volume and improve printing clarity. This pressure must be horizontally tangent to both ends of the anilox roller, without any deviation, otherwise it will affect the clarity and printing effect of the printed material.

 

2. Pressure of ink transfer device:
  
The function of the printing pressure between the metal mesh roller and the printing plate roller is to evenly transfer the ink on the metal mesh roller to the printing surface (protruding printing part) of the printing plate.
  
The correctness of this printing pressure has a great impact on the clarity of the printed dots. If the pressure is too heavy, the anilox roller will exert greater pressure on the printing plate, resulting in an enlarged image dot after printing. (Thickening or double shading of characters and lines), 10% of the high key points can be expanded to 20% of the points, the middle key points jump up, the gradient level becomes darker and deeper, the low-key level points disappear, and more than 60% of the points are almost solid. From the magnifying glass, it can be observed that each dot is in a double shadow overlapping enlarged state (1-60%). More than 60% of the branches are no longer visible and are in physical condition.
  
The products printed in this way suffer from loss of tone levels, poor image clarity, poor color tone reproduction, and inability to balance the three colors; At the same time, due to excessive printing pressure, the durability of the printing plate decreases, and it is prone to ink accumulation, resulting in problems such as dirt and stains during printing. If the pressure is too light, the ink on the printing plate cannot be absorbed, and of course, the best printing effect cannot be achieved.
  
Adjust the pressure at both ends of the anilox roller and the printing plate roller to match their size, and ensure that the ink layer on the anilox roller is in direct contact with the circular cutting of the printing plate. Of course, this "perfectly in contact with the circular cutting level" requires long-term operational practice to obtain.
  
3. Pressure of the embossing device:
  
This pressure refers to the printing pressure between the plate roller and the embossing roller. The pressure to ensure that the ink layer obtained on the printing plate is correctly transferred onto the substrate is the final key to flexographic printing, which directly affects the quality of the printed product. Excessive pressure between the two rollers causes the printed dots to spread out, with a light color in the middle and deep circles around, which has a significant impact on the image hierarchy (text and line plates spread out on both sides of the imprint). The dark tone hierarchy is prone to blur, and if the pressure is too light, the image cannot be printed on the substrate.
  
The correct pressure adjustment should be to ensure that the pressure on both ends of the imprinting roller and the printing plate roller is adjusted to be consistent, with the two in a circular cut horizontal contact. When the ink surface of the printing plate is in contact with the printing material, the dot is basically not enlarged, the words and lines are clear, and there is no double printing spread. It is best to print all the images. At the same time, during the printing process, adjustments should be made at any time according to the specific printing situation to maintain the best state.

Send Inquiry