Flexographic printing machines are widely used in the packaging industry due to their efficiency, versatility, and ability to print on a variety of substrates. However, to achieve high - quality prints, proper calibration of the flexographic printing machine is essential. As a supplier of Flexographic Printing Machines, I would like to share some key steps and considerations on how to calibrate a flexographic printing machine.


1. Pre - calibration Preparation
Before starting the calibration process, it is crucial to ensure that the machine is in a proper working condition. Check all the mechanical parts for any signs of wear and tear, such as loose belts, damaged gears, or misaligned rollers. Make sure that the ink supply system is clean and free of any blockages. Also, ensure that the anilox rolls and printing plates are in good condition.
Inspect the anilox rolls for any scratches or clogging. A damaged anilox roll can lead to uneven ink transfer, resulting in poor print quality. If necessary, clean the anilox rolls using appropriate cleaning agents and equipment. Similarly, examine the printing plates for any defects, such as cracks or missing parts. Replace any damaged plates before calibration.
2. Register Calibration
Register calibration is one of the most important aspects of flexographic printing machine calibration. It ensures that all the colors are printed in the correct position relative to each other. To start the register calibration, first, set up a test print job with a simple design that includes multiple colors.
Use the machine's register control system to adjust the position of each printing unit. Most modern flexographic printing machines are equipped with electronic register control systems that allow for precise adjustments. Start by adjusting the lateral register, which controls the side - to - side position of the print. Then, adjust the longitudinal register, which controls the front - to - back position.
Check the register accuracy by measuring the distance between the different color elements on the test print using a magnifying glass or a register gauge. Make small adjustments to the register controls until the desired accuracy is achieved. A common tolerance for register accuracy in flexographic printing is within ±0.1 mm.
3. Ink Density Calibration
Ink density calibration is another critical step in achieving consistent print quality. The ink density affects the color intensity and the overall appearance of the print. To calibrate the ink density, first, select a color - measuring device, such as a densitometer.
Print a test pattern with solid color areas for each ink color. Measure the ink density of these solid areas using the densitometer. Compare the measured values with the target ink density values, which are usually specified by the customer or determined based on industry standards.
To adjust the ink density, you can change the anilox roll cell volume, the ink viscosity, or the pressure between the anilox roll and the printing plate. Increasing the anilox roll cell volume will generally increase the ink transfer and thus the ink density. However, this may also lead to an increase in ink splashing or over - inking. Adjusting the ink viscosity can also have a significant impact on ink density. A higher viscosity ink will generally result in a higher ink density.
4. Plate Cylinder and Anilox Roll Pressure Calibration
Proper pressure between the plate cylinder and the anilox roll is essential for uniform ink transfer. Incorrect pressure can lead to issues such as ink starvation, over - inking, or uneven print quality. To calibrate the pressure, use a pressure - measuring device, such as a pressure - sensitive film.
Place the pressure - sensitive film between the plate cylinder and the anilox roll at several points around the circumference of the rolls. Rotate the rolls slowly to transfer the pressure pattern onto the film. Analyze the pressure pattern on the film to determine if the pressure is uniform.
If the pressure is not uniform, adjust the pressure adjustment screws on the machine. Make small adjustments and repeat the pressure measurement process until the pressure is evenly distributed across the entire width of the rolls. The ideal pressure between the plate cylinder and the anilox roll depends on the type of substrate, the ink, and the printing plate, but it is typically in the range of 0.1 - 0.3 mm of compression.
5. Drying System Calibration
The drying system in a flexographic printing machine is responsible for quickly drying the printed ink on the substrate. Improper drying can lead to issues such as smudging, blocking, or poor adhesion of the ink. To calibrate the drying system, first, measure the temperature and airflow in the drying chambers.
Use a temperature sensor to measure the temperature at different points in the drying chambers. Ensure that the temperature is within the recommended range for the type of ink and substrate being used. Adjust the heating elements or the airflow controls to maintain a consistent temperature.
Similarly, measure the airflow using an anemometer. The airflow should be sufficient to remove the solvent vapors from the drying chambers and to ensure proper drying of the ink. Adjust the fans or the air ducts if necessary to achieve the desired airflow.
6. Substrate Tension Calibration
Proper substrate tension is crucial for smooth feeding and accurate printing. Incorrect substrate tension can lead to issues such as wrinkling, stretching, or misregistration. To calibrate the substrate tension, use a tension - measuring device, such as a tension sensor.
Measure the substrate tension at different points along the web path, including the unwind, the printing units, and the rewind. Adjust the tension control systems, such as the brakes and clutches, to maintain a consistent tension throughout the printing process.
The ideal substrate tension depends on the type and thickness of the substrate. For example, thinner substrates generally require lower tension, while thicker substrates can tolerate higher tension. A common tension range for plastic films is between 10 - 50 N/m, while for paper substrates, it can be between 20 - 80 N/m.
Conclusion
Calibrating a flexographic printing machine is a complex but essential process that requires attention to detail and the use of appropriate tools and techniques. By following the steps outlined above, you can ensure that your flexographic printing machine is operating at its optimal performance, resulting in high - quality prints and increased productivity.
As a supplier of Flexographic Printing Machines, we offer a range of high - quality machines, including the High Speed Ci Flexo Printing Machine, the 6 Color Central Drum Flexo Plastic Printing Machine For Plastic Film, and the 4 Color 1600mm CI Type Paper Facial Tissues Flexo Printing Machine. If you are interested in purchasing a flexographic printing machine or need further assistance with calibration and maintenance, please feel free to contact us for a detailed discussion and negotiation.
References
- “Flexographic Printing Technology” by the Flexographic Technical Association
- “Principles of Flexographic Printing” by various industry experts
- Manufacturer's manuals for flexographic printing machines
